Issue 6
V-9908 MESSAGE/PAGE PANEL
Introduction
These instructions contain the specifications and
guidelines necessary to install, operate, and
maintain the V-9908, Message/Page Panel.
The V-9908 Message/Page Panel provides a
handheld push-to-talk microphone for live pages and
storage for eight messages. The V-9908 is
compatible with all Valcom self-amplified speakers.
The microphone, power and internal memory are
monitored, with visual and audible indicators if any
fault conditions are detected. When used with
Valcom Supervised Distributed Amplified One-Way
Paging Speakers and Horns, full system supervision
including the speaker audio path is possible.
Microphone Input
Input Impedance:
Input sensitivity:
>5000 Ohms
1kHz 1 millivolt for -12dBm
output (output terminated with 100 Ohms)
Audio
Frequency Response:
Mic – Output:
Frequency Response:
Stored Messages – Output:
Input Sensitivity (mic):
output (output terminated with 100 Ohms)
Signal to Noise (Idle mode, Ref -12dBm):
Signal to Noise (Mic active, Ref -12dBm)
Distortion (Mic – Output):
Output Impedance:
Nominal output level:
Maximum output level:
150Hz – 7,000Hz
Applications
Valcom Supervised Distributed Amplified
One-Way Paging Systems.
150Hz – 3,500Hz
1kHz 1 millivolt for -12dBm
Refer to Figure 1 for a block diagram of a typical
installation.
>70dB
>50dB
< 1% THD at -12dBm
< 25 Ohms
Features
Dynamic noise canceling handheld microphone
for live page
-12dBm (Ref 600 Ohms)
0dBm (before clipping)
Provides up to 8 minutes of high quality digital
recording
Stores and plays up to 8 messages
Eight (8) preprogrammed messages included
PC Programmable
Message panel fully supervised
Provides speaker line supervision
Provides microphone supervision
Provides DC power supervision
Allows remote message activation
Visual and audible system trouble indication
Audible signal cancel button
System Supervision
Main Audio Channel:
30Hz tone (inaudible)
Microphone:
1kHz tone supervises the preamp,
cable and element
Microphone Switch: DC loop with 4.7K Ohm resistor
Audio Output: DC loop terminated with a 4.7K Ohm
1/4W resistor
Voice Storage Memory:
Fixed segment memory
monitoring
Main Power:
Battery:
9VDC battery provides redundant
supervision power
Power "ON" indicator
Mounts in most 4 gang deep electrical box
Low voltage monitoring
All system faults are indicated by both an audible
and visual alarm. The audible alarm may be
silenced, however, the visual indicator will continue
to illuminate until the fault is removed.
Dimensions
5"W x 4.25"H x 2”D
(12.7cm W x 10.8cm D x 5.08cm H)
4 lbs. (1.5Kg)
User Controls (Figure 1)
Push-to-Talk Microphone
Specifications
Power Requirements
Operating Voltage 22 – 26VDC
Current 250mA
Pushbuttons to activate pre-recorded messages
Pushbutton to cancel message play
Pushbutton to cancel wire fault alarm
947980
1
Figure 1 shows microphone, message activate
and fault indication control locations.
System Troubleshooting
There are 4 LED’s located on the PC board for
system troubleshooting. They are:
LED D9 - Mic. Switch Fault
Figure 2 shows remote message activate terminal
connections, output connections, programming
and power connections located on the back of the
message panel.
(ON = fault detected)
LED D10 - DC Fault (low battery or
internal monitoring System fault)
(ON = fault detected)
Figure 3 shows a typical connecting arrangement
and other feature connections for a Fully
Supervised system, including speaker wire run
supervision. Fully supervised systems require a
Valcom V-9999 End of Line terminator (not
included). Refer to Figure 3 to connect the
message active contact and remote activation of
the messages. Using a RJ-45 connector, connect
speaker audio (Tip and Ring) and speaker power
to board mounted connector as shown on
connecting diagram. (A remote mounted
connecting block will be required to access these
connections.) Referring to Figure 3, connect
24VDC as indicated.
LED D11 - Audio loop back fault
(ON = Fault in Mic. audio or 30Hz
amplifier loop back)
LED D12 - Flash Memory Error
(ON = Checksum failed)
TECHNICAL ASSISTANCE
When trouble is reported, verify the unit is
turned on and there are no broken
connections leading to the unit.
Assistance in troubleshooting is available from
the factory. When calling, you should have a
VOM and a test set and call from the job site.
Call (540) 563-2000 and press 1 for Technical
Support, or visit our website at
When installed without full wire run supervision, a
Valcom V-1096 Audio Interface is required to be
installed inline on the audio output between the
V-9908 Message Panel and the first connected
device (page control or speaker – refer to page 5
for details)
Valcom equipment is not field repairable.
Valcom maintains service facilities in
Roanoke, VA. Should repairs be necessary,
attach a tag to the unit clearly stating company
name, address, phone number, contact
person, and the nature of the problem.
Send the unit to:
Programming the Message Panel
Refer to the programming guide included with the
message panel documentation.
Valcom, Inc.
Repair and Return Dept.
5614 Hollins Road
Roanoke, VA 24019-5056
VALCOM LIMITED WARRANTY
Valcom, Inc. warrants its products only to the original purchaser, for its own use, to be free from defects in materials and workmanship under
conditions of normal use and service for a period of one year from the date of shipment. This Limited Warranty obligation shall be limited to the
replacement, repair or refund of any such defective device within the warranty period, provided that:
1. inspection by Valcom, Inc. indicates the validity of the claim;
2. the defect is not the result of damage, misuse or negligence after the original shipment;
3. the product has not been altered in any way or repaired by others and that factory sealed units are unopened (a service charge plus parts
and labor will be applied to units defaced or physically damaged);
4. freight charges for the return of products to Valcom are prepaid;
5. all units 'out of warranty' are subject to a service charge. The service charge will cover minor repairs (major repairs will be subject to
additional charges for parts and labor).
This Limited Warranty is in lieu of and excludes all other warranties, expressed or implied and in no event shall Valcom, Inc. be liable
for any anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in connection with the purchase,
operation, maintenance, installation, removal or use of the product. The maximum liability of Valcom under this warranty is limited to
the purchase price of the specific Product covered by the warranty.
Disclaimer. Except for the Limited Warranty provided herein, the product is provided “as-is” without any warranty of any kind whatsoever
including, without limitation, any WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT.
This warranty specifically excludes damage incurred in shipment. In the event a product is received in damaged condition, the carrier should be
notified immediately. Claims for such damage should be filed with the carrier involved in accordance with the F.O.B. point.
Headquarters:
Valcom, Inc.
5614 Hollins Road Roanoke, VA 24019-5056
Phone: (540) 563-2000 FAX: (540) 362-9800
947980
3
Noise Canceling Handheld
Push to Talk Microphone
Message Cancel
Button
Eight (8) Message
Play Buttons
Eight (8) Message
Play Indicators
Message Label
Window
Fault Audible
Cancel Button
System Fault
Indicator
Figure 1: User Control Locations
Message Activate
Contact Closure Inputs
Serial Programming
Input
9 V Alkaline
Battery
Output
Connections
24VDC Input
Power Connection
RJ45 Pin Assignment
Pin 1 Audio Out
Pin 2 Audio Out
Pin 3 Supervision 4.7K resistor (A “no fault” condition results in 4.7K ohm between pins 3 and 6)
Pin 4 Message Play Contact (Pins 4 and 5 short when audio is present on pins 1 and 2)
Pin 5 Message Play Contact
Pin 6 Supervision 4.7K resistor
Pin 7 24VDC
Pin 8 24VDC Common
Figure 2: Rear Connections
947980
4
Remote Activation
Single Pole Switch
Valcom Amplified
Supervised Speakers
Remote Message Play Inputs
RS 232
Program Port
Laptop computer
Connect field wiring
directly to speaker
terminals or speaker
pigtails.
Tip
Ring
Tip
Gnd
-24vdc
Ring
Gnd
-24vdc
COM
- 24VDC
V-9999
EOL
Terminator
not included
9 Volt Alkaline
Battery
Figure 3: Typical Connections - Fully Supervised System
Default shorting jumper
positions are shown.
(from top to bottom –
up, up, down).
Shorting
Jumper
Position
1
2
3
V-1096
AUDIO ADAPTER
The only time that these
need to be moved is
when connecting the
output of the V-1096 to
a lo-z microphone input.
In this case, all of the
jumpers must be moved.
(From top to bottom -
down, down, up)
Shorting
Jumper
Position
1
2
3
1
Shorting
Jumper
Position
2
3
When the V-9908 is not being used as shown in Figure 3, a V-1096 Audio Adapter must be
utilized.
1) Connect the audio output of the V-9908 to the audio input of the V-1096.
2) Connect the audio output of the V-1096 to the audio input of the receiving system.
Examples of receiving systems include a tip/ring telephone input on a Valcom Page
Control, the tip/ring audio input of one or more Valcom Self Amplified Speakers, a line
level music or auxiliary input on a Valcom page control, IP Audio gateway or amplifier, or
a lo-z microphone input. In the case of a lo-z microphone input, such as that found on
Valcom MultiPath or Class Connection systems, all of the shorting jumpers must be
moved from the default positions shown above.
3) If the audio input of the receiving system requires a “loop start” connection, then connect
the message play contacts of the V-9908 to the Contact Closure input of the V-1096.
4) If the audio input of the receiving system requires an activation closure, then connect the
message play contacts of the V-9908 to the activation input of the receiving system.
947980
5
Preprogrammed Messages included in the V-9908
*In order to personalize these messages, please refer to content found on
the CD included with the V-9908.
Message 1: (Triple buzz, repeated three times) “May I have your attention, please. A fire
emergency has been reported in the building. While this is being verified,
please leave the building by the nearest exit or exit stairway. Do not use the
elevators”.
Message 2: (Triple buzz, repeated three times) “May I have your attention, please. An
emergency has been reported in the building. While this is being verified,
please leave the building and report to the designated assembly area for your
group”.
Message 3: May I have your attention, please. “The National Weather Service has issued a
Severe Weather Warning for our area”.
Message 4: (Triple buzz, repeated three times) “May I have your attention, please. A fire
emergency has been reported in the building. While this is being verified,
please leave the building by the nearest exit”.
Message 5: (Whoop tone twice) “May I have your attention, please. An emergency has
been reported in the building. While this is being verified, please, stand by for
further instructions”.
Message 6: (Chime three times) “May I have your attention, please. The building
emergency has ended; an all clear has been given. Please resume normal
activities”.
Message 7: “This is a test of the building public announcement system. This system is
designed to provide up to the minute communications to the workforce during
emergencies. In an Emergency a professional security force will provide real
time verbal exit instructions to specific zones within the complex, or to the
entire complex from the central alarm station in the security office. This is a
test”.
Message 8: (Train Whistle)
Table 1
947980
6
|