TROUBLE SHOOTING GUIDE
WATER LEVEL ADJUSTMENT
1. PROBLEM: Fill valve turns on/ off without toilet being flushed
1. To adjust, simply turn upper half of valve counter-clockwise
INSTALLATION INSTRUCTIONS
a. PROBABLE CAUSE: No proper slack in flapper chain to unlock, pull up til water level is where the water line is marked on
SOLUTION: Adjust for proper slack
b. PROBABLE CAUSE: Flush valve flapper dirty
SOLUTION: Inspect and clean
the overflow pipe, Fig. C, then turn clockwise till valve
snaps into locked position.
2. Turn on
For MS904114 / MS884114 / MS874114S / MS914114
water supply
to fill tank.
3. Tamper
proof key is
2. PROBLEM: Fill valve continues running
a. PROBABLE CAUSE: Dirty fill valve seal
SOLUTION: Shut off water supply. Open fill valve
cap and clean valve seal
1
4
IMPORTANT
optional, and may be used
simply to prevent further
adjustment once final setting
is achieved, Fig. D.
b. PROBABLE CAUSE: Flush valve flapper does not
seat properly
Read these instruc-
tions thoroughly
before beginning
work.
SOLUTION : Inspect, clean or adjust flapper position
c
a
b
3. PROBLEM: Poor Flush
a. PROBABLE CAUSE: Trapway is obstructed
SOLUTION: Unclog trapway
b. PROBABLE CAUSE: Supply stop is partially closed
SOLUTION: Open supply stop
c. PROBABLE CAUSE: Venting is obstructed
SOLUTION: Clear venting pipe
d. PROBABLE CAUSE: Water supply is too low
SOLUTION: The minimum required supply pressure
is 20 psi. Consult your plumber.
d
You have purchased
one of the best
working toilets
available today,
backed by TOTO’s
worldwide finest
reputation.
2
SERVICING
INSTRUCTIONS
3
1. Turn off water supply, then
flush toilet.
f
5
TSU01W
2
3
2. Snap off cover.
Please leave instructions for customers. These instructions
contain maintenance and warranty information.
3. Gently press float arms inward and
remove float.
4. PROBLEM: No flushing
e
a. PROBABLE CAUSE: Supply stop is closed
SOLUTION: Open supply stop
b. PROBABLE CAUSE: Flush valve chain is too loose
or disconnected
COMMON TOOLS NEEDED:
• 12” pipe wrench
• 10” adjustable wrench
• Carpenter’s level
• Tape measure
• Plier
4. While holding valve with one hand,
twist cap 1/ 8 turn counter clock-
wise and remove.
Model
A
B
C
D
SOLUTION: Adjust chain length as needed
MS904114
MS884114
29-1/ 2” 15”
23-1/ 2” 21-1/ 4”
23-3/ 4” 16-1/ 2”
27-1/ 2” 16-1/ 2”
24-7/ 8” 17-3/ 4”
5. Lift out center tube as shown.
WARNING! DO NOT USE IN-TANK BOWL CLEANERS
28”
28”
28”
15”
15”
15”
• Screwdriver
• Putty knife
The use of high concentration of chlorine or chlorine-related products can
seriously damage fittings in the tank. This damage can cause leakage and
property damage. • TOTO shall not be responsible or liable for any tank fit-
ting failure or damage caused by the use of in-tank bowl cleaners.
6. Remove strainer form center tube
as shown. Clean strainer and cap
by rinsing off under faucet.
MS874114S(SG)
• Drill motor, 11/ 64” drill bit (for wood floor
installation) & 1/ 4” masonry drill bit (for masonry/ tile
floor installation)
MS914114
7. Carefully reassemble the valve in
the reverse order.
* Check for correct dimension
TOILET TANK FILL VALVE INSTRUCTIONS
G-Max /Power Gravity
MATERIALS REQUIRED:
• Supply tube / connector
• Supply stop
• Mounting bolts (2)
• Wax ring / seal
4
5
IMPORTANT:
INSTALLATION
1. Shut off water supply. Flush toilet;
sponge remaining water from tank.
Remove old ballcock.
2. Slide threaded valve-shaft through hole in
bottom of tank. Note:
Note position of cap when properly
assembled to the body. The ribs on
the cap are in line with the float
chamber and the refill port is aligned
as shown.
A
D
3/4"
Package Content:
No. Item
Quantity
Be sure to install
valve in the locked
position at the angle
shown in fig. A.
Thread mounting-
nut onto exposed
1.
2.
3.
4.
5.
Vitreous China Bowl w/ lid ..............................................1
Cover Plate ..............................................................................2
Top Mount Bolt Set (for seat) ........................................1
Toilet Seat Set ........................................................................1
UNIFIT Rough-In (TSU01W.12) .................................1
5a. Toilet Mounting Bolt (T-Bolt) ...............................2
5b. T-Bolt Washer................................................................2
5c. T-Bolt Nut.......................................................................2
5d. Mounting Screw w/ washer....................................4
5e. Anchor ..............................................................................4
5f. PVC Outlet Connection*..........................................1
C
B
4-1/2" *
shaft under tank and tighten nut.
DO NOT OVERTIGHTEN.
3. Connect water supply as shown in fig. B.
Pipe dope is not recommended. Hand tight-
en only; do not overtighten coupling nut.
4. Finally attach refill tube to valve and clip
other end to overflow pipe.
10"
12"
14"
8" *
(Only for MS904114)
10" *
6
7
TOTO U.S.A., INC. • 1155 Southern Road, Morrow, GA 30260
Tel. (770) 282-8686 • Fax. (770) 282-8701
NOTE: Water supply rough-in
significantly wider than standard 5"rough-in.
Consult your builder or contractor.
Printed in U.S.A. © TOTO LTD.
REV 03/01
OGU003Z
|
Texas Instruments Stereo Amplifier TAS5508 5142K7EVM User Manual
Toshiba Satellite TV System 1805 User Manual
Trane Air Conditioner RT PRC010 EN User Manual
Triarch Indoor Furnishings 60165 User Manual
Triarch Indoor Furnishings 75366 10 User Manual
Tripp Lite Battery Charger BP12V81 User Manual
Tripp Lite TV Cables B015 000 User Manual
Uniden Telephone DECT1588 User Manual
VeriFone IP Phone Omni 37xx User Manual
Vermont Casting Outdoor Fireplace BC36 User Manual