Toshiba Digital Camera IK HR1D User Manual

CMOS COLOR CAMERA  
INSTRUCTION MANUAL  
IK-HR1D  
For Customer Use  
Enter below the Serial #  
which is located on the  
bottom of the cabinet. Retain  
this information for future ref-  
erence.  
Model #  
Serial #  
IK-HR1D  
FCC NOTICE  
This equipment has been tested and found to comply with the limits for a Class A digital device, pursu-  
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against  
harmful interference when the equipment is operated in a commercial environment. This equipment  
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance  
with the instruction manual, may cause harmful interference to radio communications. Operation of this  
equipment in a residential area is likely to cause harmful interference in which case the user will be  
required to correct the interference at his own expense.  
USER-INSTALLER CAUTION:Your authority to operate this FCC verified equipment could be voided if  
you make changes or modifications not expressly approved by the party responsible for compliance to  
Part 15 of the FCC Rules.  
This Class A digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe A est comforme à la norme NMB-003 du Canada.  
Following information is only for EU-member states:  
The use of the symbol indicates that this product may not be treated as household waste.  
By ensuring this product is disposed of correctly, you will help prevent potential negative  
consequences for the environment and human health, which could otherwise be caused by  
inappropriate waste handling of this product. For more detailed information about the take-  
back and recycling of this product, please contact your supplier where you purchased the  
product or consult.  
This manual is made from recycled paper.  
 
Note the following instructions when installing.  
• Do not cover the product with any material.  
• Do not place the product on any inflammable material such as a carpet or  
blanket.  
• Do not place the product in a confined space, as this may cause heat to  
build up inside the product.  
Failure to follow the above cautions may result in fire.  
Do not place the product in direct sunshine and/or high temperature.  
Temperature build up inside the product may result in fire.  
Avoid placing in humid, smoky, or dusty places.  
This may result in fire and/or electrical shock.  
Do not point the lens directly at the sun and/or intensive light such as di-  
rect sunlight, etc.  
Focusing of the light may result in eye injury and/or fire.  
Ask your dealer to perform a periodical check and internal cleaning (approx.  
once every five years).  
Dust inside the product may result in fire. For check and cleaning cost, please  
consult your dealer.  
Disclaimer  
We disclaim any responsibility and shall be held harmless for any damages or losses incurred by the  
user in any of the following cases:  
1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether inten-  
tional or accidental; use under extreme operating conditions.  
2. Malfunction or non-function resulting in indirect, additional or consequential damages, including  
but not limited to loss of expected income and suspension of business activities.  
3. Incorrect use not in compliance with instructions in this instruction manual.  
4. Malfunctions resulting from misconnection to other equipment.  
5. Repairs or modifications made by the user or caused to be made by the user and carried out by  
an unauthorized third party.  
6. Notwithstanding the foregoing, Toshiba’s liabilities shall not, in any circumstances, exceed the  
purchase price of the product.  
Copyright and Right of Portrait  
There may be a conflict with the Copyright Law and other laws when a customer uses, displays,  
distributes, or exhibits an image picked up by the camera without permission from the copyright  
holder. Please also note that transfer of an image or file covered by copyright is restricted to use  
within the scope permitted by the Copyright Law.  
Protection of Personal Information  
Images taken by the camera that reveal the likeness of an individual person may be considered  
personal information. To disclose, exhibit or transmit those images over the internet or otherwise,  
consent of the person may be required.  
3
 
Limitation of Usage  
The product is not designed for any “critical applications.Critical applications” means life support  
systems, exhaust or smoke extraction applications, medical applications, commercial aviation, mass  
transit applications, military applications, homeland security applications, nuclear facilities or systems  
or any other applications where product failure could lead to injury to persons or loss of life or  
catastrophic property damage. Accordingly, [Toshiba/TAIS] disclaims any and all liability arising out of  
the use of the product in any critical applications.  
TABLE OF CONTENTS  
1
2
3
4
CAUTIONS ON USE AND INSTALLATION ............................................ 6  
COMPONENTS ....................................................................................... 6  
NAMES AND FUNCTIONS...................................................................... 7  
CONNECTION........................................................................................  
4.1 Standard Connection ..................................................................................................  
4.2 Cautions on Connection..............................................................................................  
4.3 Connection on Rear Panel..........................................................................................  
4.3A Connector Pin Assignments .....................................................................................  
8
8
8
9
9
5
OPERATION............................................................................................ 10  
5.1 White Balance.............................................................................................................. 10  
5.2 Gain ............................................................................................................................. 12  
5.3 Switching I/P mode ......................................................................................................12  
6
7
ITEMS CONTROLLED BY THE ON SCREEN DISPLAY........................ 13  
MODE SETTING BY THE ON SCREEN DISPLAY ................................  
14  
7.1 Using the Menus......................................................................................................... 14  
7.2 Scene File................................................................................................................... 14  
7.3 Menus ......................................................................................................................... 15  
(1) SHUTTER (Electronic shutter) .................................................................................... 15  
(1.1) Changing the setting in AUTO mode................................................................... 15  
(1.2) Changing the setting in MANUAL mode.............................................................. 17  
(1.3) Changing the setting in SS (Synchro Scan) mode .............................................. 17  
(2) GAIN (Video gain) ....................................................................................................... 18  
(2.1) Changing gain in MANUAL mode........................................................................ 18  
(3) WHT BAL (White Balance).......................................................................................... 18  
(3.1) Changing the setting in AWB (Automatic White Balance) mode ........................ 18  
(3.2) Changing the setting in ATW (Automatic Tracking White balance) mode ......... 20  
(3.3) Changing gain in MANUAL mode ....................................................................... 21  
(4) PROCESS ................................................................................................................... 22  
(4.1) Changing gamma correction ON/OFF ................................................................ 22  
(4.2) Changing gamma correction level....................................................................... 22  
(4.3) Changing detail (outline) gain.............................................................................. 23  
(4.4) Changing DTL B. FRQ (detail boost frequency)............................................... 23  
(4.5) Changing master pedestal .................................................................................. 23  
(5) MATRIX(Matrix color correction)................................................................................. 24  
(5.1) Changing Matrix color correction ON/OFF .......................................................... 24  
(5.2) Changing MATRIX setting................................................................................... 24  
4
 
(6) OPTION....................................................................................................................... 25  
(6.1) Changing a type of output monitors .................................................................... 25  
(6.2) Changing I/P MODE ...........................................................................................  
25  
(6.3) Changing RS 232C baud rate ............................................................................  
25  
(7) Returning to factory settings .......................................................................................  
BEFORE MAKING SERVICE CALL........................................................  
SPECIFICATIONS..................................................................................  
25  
26  
26  
27  
8
9
10 EXTERNAL APPEARANCE DIAGRAM................................................  
5
 
1. CAUTIONS ON USE AND INSTALLATION  
Handling the unit.  
Do not shoot intense light.  
When intense light enters, vertical stripes or  
transverse band may appear on the screen. This  
is not a malfunction. Ghosts may occur when  
there is an intense light near the object. In this  
case, change the shooting angle.  
Do not drop, jolt, or vibrate, as this may result in  
damage to the unit. This may cause problems.  
Treat the camera cables carefully to prevent  
cable problems, such as breaks in the cable and  
loose connections.  
Install the camera in a location free from noise.  
Moire  
If the camera or the cables are located near power  
utility lines or a TV, etc. undesirable noise may ap-  
pear on the screen. In such a case, try to change  
the location of the camera or the cable wiring.  
A moire pattern is an interference pattern  
generated when two repetitive line patterns  
overlap. This is not a malfunction. Eliminating the  
repetitive line patterns, or aligning the two  
patterns, will eliminate the moire.  
Operating ambient temperature and humidity.  
Handling of the protection cap.  
Do not use the camera in places where tempera-  
ture and humidity exceed the specifications. Pic-  
ture quality will deteriolate and internal parts may  
be damaged.  
Keep the protection cap away from children as  
they may pose a choking hazard. The protection  
cap protects the image sensing plane when the  
lens is removed from the camera head, do not  
discard.  
Be particularly careful when using in places ex-  
posed to direct sunlight. When shooting in hot  
places, depending on the conditions of the object  
and the camera (for example when the gain is in-  
creased), noise in the form of vertical strips or  
white dots may occur.  
When cleaning the camera.  
Unplug the power source before cleaning. Clean  
with a soft dry cloth only. Do not use any chemicals  
or chemically treated cloths. Chemicals may  
damage coatings, printing or the paint work.  
When cleaning the lens, use lens cleaning paper.  
This is not a malfunction.  
When not using the camera for extended  
periods of time.  
Installation without a tripod.  
Switch the control unit off and disconnect the  
power supply.  
Before installing the camera, make sure that the  
location can withstand the total weight of the  
camera.  
Avoid using or storing the camera in the fol-  
lowing places:  
If this is not the case, reinforce the area to  
prevent the unit from dropping, which may result  
in damage to the unit or personal injury.  
Places filled with highly flammable gas.  
Places near gasoline, benzene, or paint thinner.  
Places subject to strong vibration.  
This camera is for indoor use only.  
Places containing chemicals (such as pesticides),  
rubber or vinyl products for extended periods of  
time.  
2. COMPONENTS  
1
2
Camera ................................................................................................................... 1  
Accessories  
Instruction manual ........................................................................................ 1  
a
6
 
3. NAMES AND FUNCTIONS  
1
Prism faceplate  
2 DC IN 12V terminal  
4 DISP button  
6 MENU UP button  
8
DATA UP (AWB) button  
9 DATA DOWN button  
7
MENU DOWN button  
5 PAGE button  
10  
DVI-I terminal  
3 REMOTE terminal  
[ Front ]  
[ Rear ]  
11  
12  
[ Bottom ]  
Prism faceplate  
The protection cap is attached on the lens mount portion. After removing the cap,  
mount the lens. Be careful not to scratch or touch the optical area.  
DC IN 12V terminal  
Accepts a DC power input (12V).  
REMOTE terminal  
To connect to a RS-232C device for remote control function.  
Used when switching the display.  
DISP button  
PAGE button  
Used when switching to the menu and when selecting the menus.  
Select the function to be confirmed or changed on the menu.  
Select the function to be confirmed or changed on the menu.  
MENU UP button  
MENU DOWN button  
DATA UP (AWB) button  
Changes the value of the function selected by the MENU (UP/DOWN) button. (Also  
used when using AWB.)  
DATA DOWN button  
Changes the value of the function selected by the MENU (UP/DOWN) button.  
Outputs DVI-I to connect to a DVI monitor.  
DVI-I terminal  
Mounting holes M3  
Used to attach the camera to a mount. When using a tripod, attach the mounting  
bracket: JK-KTF1 (option) to these holes.  
Mounting holes M2  
Used to attach the camera to a mount.  
7
 
4
CONNECTION  
4
1
Standard Connection  
DVI monitor  
(not supplied)  
Lens (option)  
DVI cable  
(not supplied)  
DVI terminal  
IK-HR1D  
DC IN 12V  
Less than 11 mm [0.433”]  
DC power supply  
(option)  
4
2
Cautions on Connection  
When connecting the camera cables, be sure to turn off the CMOS color camera and  
any other equipment connected to it.  
For DC power supply connecting to DC IN 12V terminal, use UL listed and/or CSA  
approved ungrounded type AC adaptor with the specifications described below.  
Power supply voltage  
Current rating  
Ripple voltage  
Connector  
12V DC 10% (The maximum voltage must not exceed 16V DC.)  
More than 830mA  
(
)
Less than 50mV p-p  
HR10A-7P-4S by HIROSE electronics Co. Ltd  
Pins 1, 2 12V  
Pins 3, 4 GND  
We suggest using a C mount lens accepted mega pixel. When using other lenses,  
the best camera performance of this camera may not be obtained.  
(For example, low resolution may occur, focus may be lost through the range of  
a zoom lens, and flare, ghost may occur.)  
Furthermore, in order to avoid damaging the mounting portion of the camera head,  
use a lens which has projection dimension from the mounting base of less than  
0.433" (11mm.)  
* This camera outputs 1080p and 1080i for the video signal. The output mode is  
not controlled automatically for the monitor resolution. Please control the  
monitor resolution, and switch the mode to "1080p" or "1080i."  
If this camera in the output mode does not accept a monitor, the monitor will not  
display anything. Refer to the item "5.3 Switching I/P mode" for the operation.  
* DVI standard  
DVI (Digital Visual Interface) is an interface standard for connecting flat panel  
displays (such as liquid crystal display).  
DVI connector has three types : DVI-I (digital and analog), DVI-D (digital only),  
and DVI-A (analog only) in accordance with a mounting signal conductor.  
Please use a DVI cable (not supplied) for an input terminal to connect this  
camera.  
8
 
4
3
Connection on Rear Panel  
Rear panel view  
1
2
4
3
㪩㪜㪤㪦㪫㪜  
1
2
3
1
9
2
3
4
5
6
7
8
C1 C2  
10 11 12 13 14 15 16  
C3 C4  
C5  
17 18 19 20 21 22 23 24  
4. 3A Connector Pin Assignments  
DC IN 12V terminal DVI-I terminal  
1
2
3
4
+12V  
+12V  
GND  
GND  
1
2
3
4
5
6
7
8
Data2-  
Data2+  
Data2 Shield (GND)  
NC  
NC  
NC  
NC  
9
Data1-  
10 Data1+  
Data1 Shield (GND)  
NC  
13 NC  
14 +5V  
15 GND  
16 Hot Plug Detect  
C2 Analog Green  
17 Data0-  
18 Data0+  
11  
12  
19  
20  
Data0 Shield (GND)  
NC  
21 NC  
22 Clock Shield (GND)  
23 Clock+  
24 Clock-  
C3 Analog Blue  
REMOTE terminal  
1
2
3
TXD  
RXD  
GND  
Analog Vertical Sync  
C1 Analog Red  
C4 Analog Horizontal Sync C5 Analog GND  
* For connecting to the REMOTE terminal, use a shielded cable. Connect a cable correctly,  
or it may be damaged.  
9
 
5
OPERATION  
Refer to the item "4. CONNECTION", and connect the equipment correctly.  
Turn on the connected equipment and the camera.  
Aim the lens at the object, adjust the lens iris adjustment, focus adjustment, etc.  
Refer to the item “5.1 White Balance”, make the adjustment.  
Refer to the items “5.2 Gain”, “5.3 Switching I/P mode”, “7. MODE SETTING BY THE ON SCREEN  
DISPLAY”, select the necessary items.  
5
1
White Balance  
For white balance adjustment of this unit, ATW (Automatic Tracking White balance), AWB (Automatic  
White Balance) and MANUAL (Manual white balance) adjustments are provided. Refer to the item “7.3 (3)  
WHT BAL (White Balance)”, select the desired mode.  
ATW  
AWB  
MANUAL  
Manual White Balance䋩  
Automatic Tracking  
Automatic White Balance䋩  
White Balance䋩  
The camera measures the  
Adjust white balance by  
Adjust the white balance  
manually using the WHT  
BAL menu while shooting  
the white object.  
Outline  
object color temperature and displaying the white object  
adjusts the white balance  
automatically.  
inside the area set by AWB  
menu and pressing the  
[DATA UP] button.  
Tracks variations of color  
Measurement accuracy is  
Artificial white balance setting.  
The manual adjustment is  
most effective under shooting  
conditions with no color  
Features temperature and adjusts white higher than ATW. This  
balance automatically.  
mode is effective when  
shooting under less varia-  
tions of color temperature.  
temperature variation.  
If illumination is low, white  
balance may not be corrected.  
Adjustment is performed by  
confirming with a monitor.  
Notes  
(1) AWB(Automatic White Balance)  
Set the MODE to AWB on the WHT BAL menu.  
Perform the C.TEMP (color temperature conversion) setting, if necessary.  
(Refer to the item “7.3 (3) WHT BAL (White Balance)”.)  
3200KAppropriate for indoor shooting.  
5600KAppropriate for outdoor shooting.  
If the color bar pattern is displayed on the screen or if the index menu/menu is displayed, press the [DISP]  
button to disable the color bar pattern or the character display on the menu.  
Shoot a known white object entirely in the area set by the AWB menu (refer to the item “7.3 (3) (3.1) (d)  
Confirming the contents of the zone area selected by AWB” ) and press [DATA UP] button for approx. 1 second.  
The character AWB blinks on the screen when the AWB starts.  
The character AWB stops blinking when the AWB finishes, and the result is displayed for approx. 1 second.  
10  
 
Display  
AWB OK  
AWB NG  
Meaning  
Automatic white balance adjustment finished correctly.  
Automatic white balance adjustment cannot be performed because the video level is  
too low.  
LEVEL LOW  
Adjust the video level by increasing the illumination or opening the lens iris.  
Automatic white balance adjustment cannot be performed because the video level is  
too high.  
AWB NG  
LEVEL HIGH  
Adjust the video level by decreasing the illumination or closing the lens iris.  
Automatic white balance adjustment cannot be performed because the color  
temperature is too low.  
AWB NG  
C. TEMP LOW  
If the C.TEMP is set to 5600K, set to 3200K.  
If the message appears with the C.TEMP set to 3200K, change the illumination or  
use a color temperature conversion filter.  
AWB NG  
C. TEMP HIGH  
Automatic white balance adjustment cannot be performed because the color  
temperature is too high.  
If the C.TEMP is set to 3200K, set to 5600K.  
If the message appears with the C.TEMP set to 5600K, change the illumination or  
use the color temperature conversion filter.  
AWB NG  
Automatic white balance adjustment cannot be performed for other reasons. Such as  
no white area is included in an object, etc.  
(2) MANUAL(Manual white balance)  
Set the MODE to MANUAL on the WHT BAL menu.  
(Refer to the item “7.3 (3) WHT BAL (White Balance)”.)  
Shoot a known white object, set the white balance by adjusting the levels of R GAIN and B GAIN on the  
menu, confirming with a monitor or a vector scope.  
(Refer to the item “7.3 (3) (3.3) Changing gain in MANUAL mode”.)  
11  
 
5
2
Gain  
When the image is dark even if the lens iris is open, change the gain (video gain) to get the desired video level.  
For gain adjustment of the unit, MANUAL (Manual), OFF (0 dB) modes are provided. Select the mode on  
the GAIN menu. (Refer to the item “7.3 (2) GAIN (Video gain)”.)  
(1) MANUAL(Manual gain)  
Gain adjustment is performed on the GAIN menu. The adjustment range is from 0 to 12dB in 1dB steps.  
(Refer to the item “7.3 (2) (2.1) Changing gain in MANUAL mode”.)  
(2) OFF  
Gain is fixed at 0 dB.  
Note:  
White, red, green, or blue dots may occur when the gain is increased. This is not a malfunction, just  
certain characteristics of the CMOS sensor becoming more visible.  
5
3
Switching I/P mode  
1080 progressive and 1080 interlace for the video output mode can be selected.  
By turning on power while [DATA UP], [DATA DOWN] button is pressed, the output mode is switched.  
When switching the video output to "1080p", turn on power while [DATA UP] button is pressed.  
Output mode becomes 1080 progressive mode. "1080p" is displayed on the screen.  
When switching the video output to "1080i", turn on power while [DATA DOWN] button is pressed.  
Output mode becomes 1080 interlace mode. "1080i" is displayed on the screen.  
12  
 
6
ITEMS CONTROLLED BY THE ON SCREEN DISPLAY  
Preset value  
(Factory setting)  
MANUAL  
Item  
Available selections  
AUTO, MANUAL, SS  
MODE  
-100  
0
100  
AUTO level  
0
00 10  
05 05  
10 00  
05 05  
10  
PRESET A  
AUTO peak : average  
AUTO response speed  
AUTO area  
1
10 20  
PRESET A, PRESET B, PRESET C,  
PRESET D, PRESET E  
OFF  
MANUAL speed  
OFF, 1/100s, 1/125s, 1/250s, 1/500s, 1/1000s  
1/2000s, 1/4000s, 1/8000s, 1/16000s, 1/32000s  
2/1125H 1123/1125H  
MANUAL, OFF  
0dB 12dB  
Syncro. scan  
MODE  
MANUAL gain  
1123/1125H  
OFF  
0dB  
MODE  
AWB, ATW, MANUAL  
3200K, 5600K  
AWB  
3200K  
0
Color temperature  
AWB R PAINT  
AWB B PAINT  
AWB area  
-10  
-10  
0
0
10  
10  
0
PRESET A, PRESET B, PRESET C,  
PRESET D, PRESET E  
PRESET A  
-10  
-10  
0
0
10  
10  
ATW R PAINT  
ATW B PAINT  
0
0
-100  
-100  
ON, OFF  
0
0
100  
100  
MANUAL R GAIN  
MANUAL B GAIN  
Gamma correction  
0
0
ON  
0
Gamma correction level -10  
0
10  
Detail gain  
-7  
0
7
0
Detail boost frequency  
Master pedestal  
HIGH, NORMAL, LOW  
HIGH  
0
-128  
0
127  
Color correction ON/OFF ON, OFF  
ON  
0
0
0
0
0
0
0
0
0
0
0
0
-15  
-15  
-15  
-15  
-15  
-15  
-15  
-15  
-15  
-15  
-15  
-15  
0
0
0
0
0
0
0
0
0
0
0
0
15  
15  
15  
15  
15  
15  
15  
15  
15  
15  
15  
15  
R hue  
R gain  
G hue  
G gain  
B hue  
B gain  
Ye hue  
Ye gain  
Cy hue  
Cy gain  
Mg hue  
Mg gain  
Monitor  
PC, TV  
PC  
I/P mode  
RS232C baud rate  
1080p, 1080i  
9600bps, 19200bps  
1080p  
9600bps  
13  
 
7
MODE SETTING BY THE ON SCREEN DISPLAY  
Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The  
contents once set are memorized in the scene files (A, B, C, D, E) selected, so if the power turns off, it is  
unnecessary to set the values again when using the unit next time. When the setting is performed, select  
the menu of the item to be set.  
7
1
Using the Menus  
When the unit is powered on, the normal screen showing only the video signal appears. Change the  
output to each screen (video signal output, color bar screen, index menu, and menus) by using the  
[DISP], [PAGE], [MENU UP], [MENU DOWN], [DATA UP], and [DATA DOWN] buttons.  
* A menu is selected when pushing the [PAGE] button after moving the “” on the screen by the [MENU  
UP], [MENU DOWN] button while the Index menu is displayed.  
POWER ON  
Video signal output  
Color bar screen  
PAGE  
Index menu  
PAGE  
DISP  
DISP  
DISP  
DISP  
PAGE  
Menus  
PAGE  
1.SHUTTER  
AUTO  
2.GAIN  
3.WHT BAL  
AWB  
4.PROCESS  
5.MATRIX  
6.OPTION  
PAGE  
PAGE  
PAGE  
PAGE  
PAGE  
GAMMA  
ON  
MANUAL  
OFF  
ON  
GAMMA  
OFF  
MANUAL  
SS  
ATW  
OFF  
MANUAL  
7
2
Scene File  
Five scene files (A, B, C, D, E) are available as user memories for this unit. These are chosen depending  
on shooting conditions. By pressing [DATA UP], [DATA DOWN] buttons while [DISP] button is pressed  
and the index menu is displayed, the camera operation is changed immediately from the currently  
selected scene file to the next. on shooting conditions. By pressing [DATA UP], [DATA DOWN] buttons  
while the Index menu is displayed, the camera operation is changed immediately from the currently  
selected scene file to the next.  
DATA UP䌝  
FILE A 
ޓ
ޓ
FILE B 
ޓ
ޓ
FILE C 
ޓ
ޓ
FILE D 
ޓ
ޓ
FILE E  
DATA DOWN䌝  
Note:  
Scene file does not contain the data of set "OPTION."  
(Refer to the item "7.3 Menus" (6) "OPTION" for the "OPTION" setting.)  
14  
 
7
3
Menus  
Select the menu to change the setting by referring to the item “7.1 Using the Menus”.  
When the [MENU UP], [MENU DOWN] buttons are pressed, the “” on the screen moves up and down.  
Move the “” to the item whose setting you wish to change.  
1
SHUTTERElectronic shutter䋩  
The electronic shutter has three modes; AUTO, MANUAL, SS(Synchro Scan).  
Press the “Page” button to enter the Shutter Page. Use the “Data Up/Down” buttons to select the Shutter  
Mode.  
DATA UP䌝  
AUTO 
ޓ
ޓ
MANUAL 
ޓ
ޓ
SS  
DATA DOWN䌝  
AUTO  
MANUAL  
The exposure time is controlled automatically to obtain the video level set.  
It is possible to select the exposure time from eleven speed settings; OFF (1/60s), 1/100s,  
1/125s, 1/250s, 1/500s, 1/1000s, 1/2000s, 1/4000s, 1/8000s, 1/16000s, 1/32000s.  
Shutter speed can be set by the horizontal scanning time (1H) unit.  
SS  
Note:  
When setting a rapid shutter speed, sensitivity degrades according to the speed.  
When a discharging light such as fluorescent lamp, etc. is used for the illumination,  
the flicker may be large.  
When an object is moving rapidly, the monitor may display the image distorted and/or  
blurred. This is not a malfunction, just certain character of the rolling shutter system.  
When the shutter speed setting is high, the hue may change depending on shooting  
conditions or objects.  
11Changing the setting in AUTO mode  
Move up and down  
by pressing  
MENU UP,DOWN  
Select the desired  
value by pressing  
DATA UP,DOWN  
Shutter mode AUTO, MANUAL, SS  
Video level adjustment -100 to 100  
-- 1 SHUTTER -- <FILE A>  
Peak and average ratio adjustment 00 10 to 10 00  
Automatic shutter response speed adjustment 1 to 20  
MODE  
AUTO  
0
05 05  
10  
LEVEL  
PEAK AVE  
SPEED  
AREA  
Automatic shutter area selection  
PRESET A, PRESET B, PRESET C, PRESET D, PRESET E  
PRESET A  
< MODE = AUTO>  
(a) Changing the video level in the automatic shutter mode  
Move the “” to LEVEL by pressing [MENU UP], [MENU DOWN] buttons.  
Select the video level by pressing [DATA UP], [DATA DOWN] buttons.  
The value increases by pressing [  
]
DATA UP  
100  
-100  
0
The value increases by pressing [  
]
DATA DOWN  
15  
 
(b) Changing the automatic shutter detection (ratio between peak and average value)  
Move the “” to PEAK/AVE by pressing [MENU UP], [MENU DOWN] buttons.  
Select the ratio between peak and average value by presshing [DATA UP], [DATA DOWN] buttons.  
(Peak:Average)  
The peak value increases by pressing [  
]
DATA UP  
10:00  
The peak value decreases by pressing [  
00:10  
05:05  
]
DATA DOWN  
(c) Changing the automatic shutter response speed  
Move the “” to SPEED by pressing [MENU UP], [MENU DOWN] buttons.  
Select the response speed by presshing [DATA UP], [DATA DOWN] buttons.  
The response speed becomes faster by pressing [  
]
DATA UP  
1
10  
20  
The response speed becomes slower by pressing [  
]
DATA DOWN  
(d) Changing the automatic shutter zone area  
Move the “” to AREA by pressing [MENU UP], [MENU DOWN] buttons.  
Select the measurement light area by pressing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
PRESET A  
PRESET B PRESET C  
PRESET D  
PRESET E  
DATA DOWN䌝  
The available picture area is shown by the shading correction on the screen that is parted in 64.  
PRESET A  
PRESET B  
PRESET C  
PRESET D  
PRESET E  
Note:  
These picture areas are not displayed on the screen.  
16  
 
12Changing the setting in MANUAL mode  
Move up and down  
by pressing  
MENU UP,DOWN  
Select the desired  
value by pressing  
DATA UP,DOWN  
Shutter mode AUTO, MANUAL, SS  
-- 1 SHUTTER -- <FILE A>  
Shutter speed setting  
OFF, 1/100s, 1/125s, 1/250s, 1/500s, 1/1000s,  
1/2000s, 1/4000s, 1/8000s, 1/16000s, 1/32000s  
MODE  
MANUAL  
MANUAL  
OFF  
< MODE = MANUAL>  
(a) Changing the shutter speed  
Move the “” to MANU by pressing [MENU UP], [MENU DOWN] buttons.  
Select the shutter speed by pressing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
OFF  
1/100s  
1/125s  
1/250s  
1/500s  
1/1000s  
1/2000s  
1/4000s  
1/8000s  
1/16000s  
1/32000s  
DATA DOWN䌝  
Note:  
These figures of shutter speed are approximate. The accurate shutter speed is calculated using the  
following mathematical formula.  
Shutter speed (s) = 1/67433 (Hz) × n (n : 2 to 1123 (integral number))  
13Changing the setting in SS (Synchro Scan) mode  
Move up and down  
by pressing  
MENU UP,DOWN  
Select the desired  
value by pressing  
DATA UP,DOWN  
Shutter mode AUTO, MANUAL, SS  
Synchro scan setting  
-- 1 SHUTTER -- <FILE A>  
MODE SS  
2/1125H  
1123/1125H  
SYNCHRO SCAN 1123/1125H  
< MODE = SS >  
(a) Changing the shutter speed setting  
Move the “” to SYNCHRO SCAN by pressing [MENU UP], [MENU DOWN] buttons.  
Select the shutter speed by pressing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
2/1125H 
ޓ
1123/1125H  
DATA DOWN䌝  
17  
 
2
GAIN (Video gain)  
GAIN has two modes; MANUAL, OFF.  
Move the “” to MODE, press the [DATA UP], [DATA DOWN], and select one of the two modes :  
MANUAL, OFF. In the OFF mode, gain is fixed to 0dB.  
21Changing gain in MANUAL mode  
Move up and down  
by pressing  
MENU UP,DOWN  
Select the desired  
value by pressing  
DATA UP,DOWN  
-- 2 GAIN --  
<FILE A>  
Gain mode MANUAL, OFF  
MODE  
MANUAL  
MANUAL  
0dB  
Manual gain setting  
0dB to 12dB (1dB step)  
Move the “” to MANUAL by pressing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of manual gain by pressing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
0dB  
12dB  
DATA DOWN䌝  
3WHT BAL(White Balance)  
The WHT BAL has three modes; AWB, ATW, MANUAL.  
Move the “” to MODE, press the [DATA UP], [DATA DOWN], and select one of the three modes :  
AWB, ATW, MANUAL.  
31Changing the setting in AWB(Automatic White Balance) mode  
Move up and down  
by pressing  
MENU UP,DOWN  
Select the desired  
value by pressing  
DATA UP,DOWN  
White balance mode setting AWB, ATW, MANUAL  
R PAINT adjustment -10 to 10  
-- 3 WHT BAL -- <FILE A>  
B PAINT adjustment -10 to 10  
MODE  
AWB  
R PAINT  
B PAINT  
C TEMP  
AREA  
0
0
Color temperature setting 3200K, 5600K  
3200K  
PRESET A  
AWB area  
PRESET A, PRESET B, PRESET C, PRESET D, PRESET E  
18  
 
(a) Changing R PAINT  
Move the “” to R PAINT by pressing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of red paint by pressing [DATA UP], [DATA DOWN] buttons.  
[
]
ޓ
Red is increased.  
DATA UP  
0
-10  
Red is decreased.  
10  
ޓ
 [  
]
DATA DOWN  
(b) Changing B PAINT  
Move the “” to B PAINT by pressing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of blue paint by pressing [DATA UP], [DATA DOWN] buttons.  
[
]
ޓ
Blue is increased.  
DATA UP  
0
-10  
10  
Blue is decreased.  
ޓ
 [  
]
DATA DOWN  
(c) Changing color temperature setting  
Move the “” to C.TEMP by pressing [MENU UP], [MENU DOWN] buttons.  
Select either 3200K or 5600K by pressing [DATA UP], [DATA DOWN] buttons.  
(d) Confirming the contents of the zone area selected by AWB  
Move the “” to AREA DISP by pressing [MENU UP], [MENU DOWN] buttons.  
Select the desired area by pressing [DATA UP], [DATA DOWN] buttons.  
The available picture area is shown by the shading correction on the screen that is parted in 64.  
PRESET A  
PRESET B  
PRESET C  
PRESET D  
PRESET E  
Note:  
These picture areas are not displayed on the screen.  
19  
 
32Changing the setting in ATW(Automatic Tracking White balance) mode  
Move up and down  
by pressing  
MENU UP,DOWN  
Select the desired  
value by pressing  
DATA UP,DOWN  
White balance mode AWB, ATW, MANUAL  
-- 3 WHT BAL -- <FILE A>  
R PAINT adjustment -10 to 10  
B PAINT adjustment -10 to 10  
MODE  
R PAINT  
B PAINT  
ATW  
0
0
(a) Changing R PAINT  
Move the “” to R PAINT by pressing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of red paint by pressing [DATA UP], [DATA DOWN] buttons.  
[
]
ޓ
Red is increased.  
DATA UP  
0
-10  
Red is decreased.  
10  
ޓ
 [  
]
DATA DOWN  
(b) Changing B PAINT  
Move the “” to B PAINT by pressing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of blue paint by pressing [DATA UP], [DATA DOWN] buttons.  
[
]
ޓ
Blue is increased.  
DATA UP  
0
-10  
10  
Blue is decreased.  
ޓ
 [  
]
DATA DOWN  
20  
 
33Changing gain in MANUAL mode  
Move up and down  
by pressing  
MENU UP,DOWN  
Select the desired  
value by pressing  
DATA UP,DOWN  
White balance mode AWB, ATW, MANUAL  
Red gain adjustment -100 to 100  
-- 3 WHT BAL -- <FILE A>  
Blue gain adjustment -100 to 100  
MODE  
R GAIN  
MANUAL  
0
Color temperature setting 3200K, 5600K  
B GAIN  
0
C TEMP  
3200k  
(a) Changing the red gain  
Move the “” to R GAIN by pressing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of red gain by pressing [DATA UP], [DATA DOWN] buttons.  
[
]
ޓ
Red is increased.  
DATA UP  
0
-100  
Red is decreased.  
100  
ޓ
 [  
]
DATA DOWN  
(b) Changing the blue gain  
Move the “” to B GAIN by pressing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of blue gain by pressing [DATA UP], [DATA DOWN] buttons.  
[
]
ޓ
Blue is increased.  
DATA UP  
0
-100  
Blue is decreased.  
100  
ޓ
 [  
]
DATA DOWN  
(c) Changing color temperature setting  
Move the ” to C.TEMP by pressing [MENU UP], [MENU DOWN] buttons.  
Select either 3200K or 5600K by pressing [DATA UP], [DATA DOWN] buttons.  
21  
 
4PROCESS  
Move up and down  
Select the desired  
value by pressing  
DATA UP,DOWN  
by pressing  
MENU UP,DOWN  
Gamma correction ON, OFF  
-- 4 PROCESS --  
GAMMA ON/OFF ON  
<FILE A>  
Gamma correction level setting -10 to 10  
Detail gain setting -7 to 7  
0
0
GAMMA  
Detail boost frequency HIGH, NORMAL, LOW  
Master pedestal setting -128 to 127  
DTL GAIN  
DTL B.FRQ  
M PED  
HIGH  
0
41Changing gamma correction ON/OFF  
Move the “” to GAMMA ON/OFF by pressing [MENU UP], [MENU DOWN] buttons.  
Select either ON or OFF by pressing [DATA UP], [DATA DOWN] buttons.  
Move up and down  
by pressing  
MENU UP,DOWN  
Select the desired  
value by pressing  
DATA UP,DOWN  
Gamma correction ON, OFF  
Detail gain setting -7 to 7  
-- 4 PROCESS --  
GAMMA ON/OFF OFF  
<FILE A>  
DTL GAIN  
DTL B.FRQ  
M PED  
0
HIGH  
0
Detail boost frequency HIGH, NORMAL, LOW  
Master pedestal setting -128 to 127  
Menu when GAMMA OFF is selected.  
42Changing gamma correction level  
Move the “” to GAMMA by pressing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of gamma correction level by pressing [DATA UP], [DATA DOWN] buttons.  
Correction amount  
becomes larger.  
10  
[
]
DATA UP  
0
-10  
Correction amount  
becomes smaller.  
[
]
DATA DOWN  
* When OFF is selected in GAMMA ON/OFF selection line, the gamma correction level cannot  
be changed.  
22  
 
43Changing detail (outline) gain  
Move the “” to DTL GAIN by pressing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of the detail gain by pressing [DATA UP], [DATA DOWN] buttons.  
[
]
ޓ
The detail increases.  
DATA UP  
0
-7  
The detail decreases.  
7
ޓ
 [  
]
DATA DOWN  
44Changing DTL B.FRQ (detail boost frequency)  
Move the “” to DTL B.FRQ by pressing [MENU UP], [MENU DOWN] buttons.  
Select the detail boost frequency by pressing [DATA UP], [DATA DOWN] buttons.  
[
]
DATA UP  
LOW  
NORMAL  
HIGH  
[
]
DATA DOWN  
45Changing master pedestal  
Move the “” to M. PED by pressing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of the master pedestal by pressing [DATA UP], [DATA DOWN] buttons.  
[
]
ޓ
M. PED increases.  
DATA UP  
0
-128  
M. PED decreases.  
127  
ޓ
 [  
]
DATA DOWN  
23  
 
5MATRIX(Matrix color correction)  
Move up and down  
Select the desired  
value by pressing  
DATA UP,DOWN  
by pressing  
MENU UP,DOWN  
Matrix color correction  
ON, OFF  
Yellow hue setting  
Red hue setting  
Red gain setting  
Green hue setting  
Green gain setting  
Blue hue setting  
Blue gain setting  
-- 5 MATRIX --  
<FILE A>  
Yellow gain setting  
Cyan hue setting  
MATRIX  
ON  
R HUE  
0
Ye HUE  
0
R GAIN  
G HUE  
G GAIN  
B HUE  
0
0
0
0
Ye GAIN  
Cy HUE  
Cy GAIN  
Mg HUE  
0
0
0
0
Cyan gain setting  
Magenta hue setting  
Magenta gain setting  
B GAIN  
0
Mg GAIN  
0
51Changing Matrix color correction ON/OFF  
Move the “” to MATRIX by pressing [MENU UP], [MENU DOWN] buttons.  
Select either ON or OFF by pressing [DATA UP], [DATA DOWN] buttons.  
52Changing MATRIX setting  
Move the “” to the desired item by pressing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of color by pressing [DATA UP], [DATA DOWN] buttons.  
[
]
DATA UP  
0
-15  
15  
[
]
DATA DOWN  
* When matrix color correction is set to OFF, the color cannot be adjusted.  
24  
 
6OPTION  
Move up and down  
Select the desired  
value by pressing  
DATA UP,DOWN  
by pressing  
MENU UP,DOWN  
-- 6 OPTION  
--  
<FILE A>  
MONITOR PC, TV  
MONITOR  
PC  
1080p  
9600bps  
I/P MODE 1080p, 1080i  
I/P MODE  
BAUD RATE  
RS232C baud rate 9600bps, 19200bps  
61Changing a type of output monitors  
Move the “” to MONITOR by pressing [MENU UP], [MENU DOWN] buttons.  
Select either PC or TV by pressing [DATA UP], [DATA DOWN] buttons.  
PC: When using PC as an output monitor.  
TV: When using TV as an output monitor.  
62Changing I/P MODE  
Interlace or progressive can be selected.  
Move the “” to I/P MODE by pressing [MENU UP], [MENU DOWN] buttons.  
Select either 1080p or 1080i by pressing [DATA UP], [DATA DOWN] buttons.  
1080p: When using 1080 progressive.  
1080i: When using 1080 interlace.  
Note:  
Select a monitor that has 1080 progressive and/or interlace modes, or the monitor will not display  
the image correctly. Refer to the item "5.3 Switching I/P mode" if selecting a wrong monitor.  
63Changing RS 232C baud rate  
Move the “” to BAUD RATE by pressing [MENU UP], [MENU DOWN] buttons.  
Select either 9600bps or 19200bps by pressing [DATA UP], [DATA DOWN] buttons.  
7Returning to factory settings  
The current setting can be returned to the factory default status (preset status).  
(1) If the color bar pattern or characters are displayed on the screen, press the [DISP] button to disable the  
color bar pattern and character display.  
(2) Press [MENU DOWN] and [DATA DOWN] buttons simultaneously for approx. 1 second.  
(3) The preset operation starts. When the preset operation finishes, the character PRESET OK is displayed  
for approx. 1 second.  
* The only selected scene file can be returned to the factory default status. Follow the instruction as  
above for every scene file when all scene files are returned to the factory default status.  
25  
 
8. BEFORE MAKING SERVICE CALL  
Symptom  
Items to be checked  
Is power supplied correctly?  
No picture  
Is the lens iris adjusted correctly?  
Are the camera and video cables connected correctly?  
Is the shutter mode set correctly?  
Is the monitor on, and in working condition?  
Is I/P mode set correctly?  
Poor color  
Is the monitor adjusted correctly?  
Is the white balance of the camera adjusted correctly?  
(in modes other than automatic tracking)  
Is the matrix color correction set correctly?  
Is the illumination sufficient?  
9. SPECIFICATIONS  
Image sensor  
Output pixels  
Signal system  
1/3 inch color CMOS sensor (Rolling shutter)  
Horizontal : 1920, Vertical : 1080  
1080/59.94i, 1080/59.94p  
Scanning system  
Scan frequency  
Sensitivity  
Progressive  
Horizontal : 67.43 kHz, Vertical : 59.94 Hz  
F 4 standard (2000 lx, 3000K)  
16 lx standard (50 IRE, F1.4, gain 12 dB,  
gamma setting ON (setting value 0), 3000 K)  
Minimum illumination  
SN ratio  
Output signal  
Sync system  
54 dB standard (gain 0 dB Y-conversion*)  
DVI-I (Digital RGB, Analog RGB) DVI-I terminal  
Internal  
H SYNC : 5 V + 0.5 V / -1.0 V (Positive polarity) DVI-I terminal  
V SYNC : 5 V + 0.5 V / -1.0 V (Positive polarity) DVI-I terminal  
ATWAutomatic tracing white balance, AWBAutomatic white balance,  
Sync signal output  
White balance  
MANUALManual䋩  
Gain  
Scene file  
MANUAL (Manual), OFF (0 dB)  
A, B, C, D, E  
Remote control  
Lens mount  
Serial data interface (RS232C)  
C mount  
Power supply  
Power consumption  
Weight  
12V DC10% (The maximum voltage must not exceed 16V DC.)  
Approx. 4.2 W  
Approx. 146 g (0.322 lbs)  
External dimension  
Operating temperature  
Operating humidity  
44(W) × 44(H) × 78(D) mm (1.73”(W) 㬍㩷1.73”(H) 㬍㩷3.07”(D) )  
0 to 40 (32F to 104F)  
Less than 90% (non condensing)  
* The SN ratio is calculated using a Y signal. Because this camera outputs a RGB signal, the Y is calculated using the following  
mathematical formula: Y=xR+yG+zB (where x, y and z are coefficients).  
Design and specifications are subject to change without notice.  
26  
 
10. EXTERNAL APPEARANCE DIAGRAM  
Unit : mm [inch]  
2-M3 Depth 3  
[0.118]  
5 [0.2]  
7.8  
[0.31]  
78 [3.07]  
44 [1.73]  
32.51[1.28]  
#4-40UNC  
[Front]  
[Rear]  
56 [2.2]  
5 [0.2]  
4-M2 Depth 3 [0.118]  
4-M3 Depth 3 [0.118]  
25 [0.98] 25 [0.98]  
27  
 
Limited Warranty – TOSHIBA CMOS Color Camera  
The Imaging Systems Division of Toshiba America Information Systems, Inc. ("ISD") makes the following limited warranties  
with regard to this CMOS color Camera ("Product"). These limited warranties extend to the Original End-User ("You[r]").  
One (1)Year Limited Warranty of Labor and Parts  
ISD warrants that this Product will perform in accordance with specifications for a period of one (1) year from the date of  
purchase by the Original End-User. During this one (1) year period, ISD will repair or replace the Product, if it does not  
perform as warranted. In order to take advantage of this Limited Warranty, You must: (a) deliver the Product to an ISD  
Authorized Service Provider ("ASP"); and (b) pay all transportation and insurance charges for shipment of the Product to the  
ASP. ISD reserves the right to substitute factory refurbished parts in place of those in need of repair.  
Instruction Manual (Owner’s Manual):  
You should read the Instruction Manual (Owner’s Manual) thoroughly before operating this Product. Before seeking warranty  
service, you should check the troubleshooting guide in the Instruction Manual (Owner’s Manual) and follow the instructions to  
correct the problem.  
Your Responsibilities  
This Limited Warranty is subject to the following conditions:  
1. You must provide the bill of sale or proof of purchase at the time that warranty service is required.  
2. You must notify an ASP within thirty (30) days after You discover that the Product does not perform in accordance with  
specifications during the Limited Warranty period.  
3. All warranty servicing of this product must be made by an ISD Authorized Service Provider.  
4. You must pack the Product in its original carton using the original packing material, then insert the original carton  
containing the Product into another carton with additional packing material before shipping the Product to an ASP.  
DISCLAIMERS:  
ALL OTHER EXPRESS OR IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. SOME STATES DO  
NOT ALLOWTHE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY  
LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TOYOU.  
IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTED ABOVE, YOUR SOLE AND EXCLUSIVE  
REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF THE PRODUCT. IN NO EVENT WILL ISD OR ITS PARENT  
COMPANY OR ANY ASP BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY DAMAGES IN EXCESS OF THE  
PURCHASE PRICE OF THE PRODUCT. THIS LIMITATION APPLIES TO DAMAGES OF ANY KIND, INCLUDING ANY  
DIRECT OR INDIRECT DAMAGES, LOST PROFITS, LOST SAVINGS OR OTHER SPECIAL, INCIDENTAL, EXEMPLARY  
OR CONSEQUENTIAL DAMAGES, WHETHER FOR BREACH OF CONTRACT, TORT OR OTHERWISE, OR WHETHER  
ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH PRODUCT, EVEN IF TAIS, ITS PARENT COMPANY, OR  
AN ASP HAS BEEN ADVISED OFTHE POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER PARTY.  
SOME STATES DO NOT ALLOWTHE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES  
FOR SOME PRODUCTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TOYOU.  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY  
VARY FROM STATE TO STATE.  
THIS LIMITED WARRANTY SHALL BE VOID IF THE PRODUCT OR PARTS HAVE BEEN SUBJECTED TO MISUSE,  
ABUSE, ACCIDENT, IMPROPER INSTALLATION, IMPROPER MAINTENANCE, OR USE IN VIOLATION OF ISD’S  
WRITTEN INSTRUCTIONS, OR WHERE THE PRODUCT HAS BEEN ALTERED OR MODIFIED WITHOUT ISD’S PRIOR  
AUTHORIZATION, OR UPON THE REMOVAL OR ALTERATION OF ISD’S FACTORY SERIAL NUMBER. LABOR  
SERVICE CHARGES FOR PRODUCT INSTALLATION, SET UP AND ADJUSTMENT OF CONTROLS ARE NOT  
COVERED BY THIS LIMITED WARRANTY.  
How to Obtain Warranty Service – Step-By-Step Procedures:  
To obtain warranty service, You should:  
1. Contact an ASP for warranty service within thirty (30) days after the Product fails to comply with specifications.  
2. Arrange for shipment of the Product to an ASP.  
3. Securely pack the Product as described above, insure the carton, and include a letter explaining the problem and a copy  
of the bill of sale or proof of purchase.  
4. Prepay all transportation and insurance costs.  
Questions? If you have any questions, please check ISD’s Web Site or send an e-mail as follows:  
No person, agent, distributor, dealer, authorized service provider, or company is authorized to change, modify, or extend the  
terms of this Limited Warranty in any manner whatsoever. The time within which an action must be commenced to enforce  
any obligation of ISD arising under this Limited Warranty or under any statute, or law of the United States or any state thereof,  
is hereby limited to one (1) year from the date You discover or should have discovered the problem. This limitation does not  
apply to implied warranties arising under state law. Some states do not permit limitation of the time within whichYou may bring  
an action beyond the limits provided by state law, so the above provision may not apply to You. This Limited Warranty gives  
You specific legal rights and You may also have other rights which vary from state to state.  
TOSHIBA AMERICA INFORMATION SYSTEMS, INC.  
Imaging Systems Division  
9740 Irvine Boulevard, Irvine, CA 92618-1697  
Copyright © 2008 Toshiba America, Inc. All rights reserved.  
 

Timex Watch W 104 User Manual
Toshiba TV DVD Combo 26LV67 User Manual
Trane Heat Pump WPVJ User Manual
Trimble Outdoors GPS Receiver SPSX51 User Manual
Tripp Lite Surge Protector Super5FR User Manual
Troy Bilt Tiller 12217 User Manual
Uniden Telephone XDECT R035 User Manual
Uniden Two Way Radio FRS500 User Manual
Univex Hot Tub 7236L User Manual
Volvo Automobile S60 S60R User Manual